• The COMPETITION FIELD consists of 24X24 SqF. The walls of the maze are 10 cm high and 1.8 cm thick (assume 5% tolerance for mazes). The maze comprises up to 22X22 SqF, for a total maze size of up to 484 SqF (assume 5-7% tolerance for mazes). The outside wall encloses the entire maze.
• The sides of the maze walls are white, the tops of the walls are red, and the floor is black. The maze is made of wood, finished with non – gloss paint.
• WARNING: Do not assume the walls are consistently white, or that the tops of the walls are consistently red, or that the floor is consistently black. Fading may occur; Parts from different mazes may be used. Do not assume the floor provides a given amount of friction. It is simply painted plywood and may be quite slick.
• The maze floor may be constructed using multiple sheets of plywood. Therefore, there may be a seam between the two sheets on which any low hanging parts of a mouse may snag
• The start of the maze is located at one of the four corners. The start square is bounded on three sides by walls.
• Multiple paths to the destination square are allowed and are to be expected. The destination square will be positioned so that a wall hugging mouse will NOT be able to find it.
• Note: Actual track design may vary from the one shown in the image below and subject to change before the event commence.

3D Model Arene: Move Cursor to View 360 degree

There will be two rounds in Fastest Line Follower gameplay i.e. Elimination round and a Final round.

• Elimination Round: This round would have total 6 minutes time period. 5 minutes for gameplay and 1 minute for bot readiness. Referee would allocate starting point randomly from where team have to start the bot. Team can select left or right hand algorithm by switching mechanism on the bot. Top 30 teams will be selected for Final Round who will reach fastest to finish line.
  •  No penalty in elimination round.
  • Within 6 minutes, team can have maximum 3 trials. Bot starts from starting point and reaching to finish point will be counted 1 trial. Fastest trial (Run Time) will be considered for next round qualifying. Once micromouse reaches to finis line, time will be paused for next trial if needed.
  • In elimination round, maximum 3 touch are allowed. Means if bot stuck in the wall or at the corner and unable to move then team can adjust the bot from stucking. (Note: Bot direction will remain same). During touch, minor hardware issue can also be fixed but maximum 30 Sec. will be allowed for reparing.
  • 3 Times bot rotation is also allowed. Means if bot stuck anywhere than team can change the direction of the bot in any direction but the position of bot will remain same.
  • After the maze is disclosed, the operator shall not feed information on the maze into the MicroMouse however, switch positions may be changed for the purpose of changing programs within the robot (changing algorithms is allowed. Entering info on the maze is not allowed and does not constitute “changing algorithms)
  • The illumination, temperature, and humidity of the room shall be those of an ambient environment. (40 to 120 degrees F, 0% to 95% humidity, non-condensing). Do not make any assumptions about the amount of sunlight, incandescent light, or fluorescent light that may be present at the contest site.
  • Every time the robot leaves the start square, a new run begins. If the robot has not entered the destination square, the previous run is aborted. For example, if a robot re-enters the start square (before entering the destination square) on a run, that run is aborted, and a new run will be deemed begun, with a new time that starts when the starting square is exited.
  • The judges reserve the right to ask the operator for an explanation of the MicroMouse. The judges also reserve the right to stop a run, declare disqualification, or give instructions as appropriate (e.g., if the structure of the maze is jeopardized by continuing operation of the robot).
  • A contestant may not feed information on the maze to the MicroMouse. Therefore, changing ROMs or downloading programs is NOT allowed once the maze is revealed. However, contestants can Change switch settings (e.g. to change algorithms. for example from left-turning to right turning – again, entering data on maze size or content is NOT inclusive of this rule), Replace batteries between run, Adjust sensors, Change speed settings, Make repairs.
• Final Round: This round would have total 10 minutes time period. 8 minutes for gameplay and 2 minutes for bot readiness. Referee would allocate starting point randomly from where team have to start the bot. After getting the starting point, team can select left or right algorithm by switching mechanism on the robot. Top 3 teams (1st, 2nd and 3rd winner) will be selected as winner based upon crossing full track in minimum time.
  • During final round, team can opt for maximum 3 trails. Shortest time will be considered for winning position.
  • Maximum 3 touches are allowed but for each touch 10 sec. will be added in bot reaching time.
  • Maximum 3 bot rotation are allowed but for each rotation 15 sec. will be added in bot reaching time.
  • Maximum 30 sec. in 8 minutes gameplay can be allocated by referee, if there is any requirement to fix hardware related issue. Time will be paused for 30 sec.

Team Members & Mentors:

• Minimum 2 members and maximum 10 members are allowed in each participating team. Multiple teams from same school/college can participate in the competition.
• Different Teams from the same school/college must use their own individual robots for the competition.
• It’s not mandatory to have coach for each team but a team can have a coach (only one) from the school or outside as a technical advisor.
• The coach will be seated in a supervisory position around the competition area and is not allowed to touch or repair the robots during the competition
• The coach should not be involved in the launching of the robots as this may lead to disqualification
• The robot must follow the design specifications provided. Any deviation from the mentioned specifications will lead to disqualification.

Fair Play:

• Robots that cause deliberate interference with other robots or damage to the field will be disqualified
• Humans that cause deliberate interference with robots or damage to the field will be disqualified.
• It is expected that the aim of all teams is to play a fair and clean game.

Behavior:

• Participants who misbehave may be asked to leave the competition area and risk being disqualified from the contest.
• The rules will be enforced at the discretion of the referees, officials, and local law enforcement authorities.

Organizing Committee:

• The organizing Committee is a union that consists of few communities and associations. The organizers of this competition are All India Council For Robotics & Automation (AICRA).
• All decisions about scoring, game play and timing are made by the juries. Teams should completely respect their vote and decisions. Members of the jury will be from different fields of the robotic science.

Venue: Muscat, Oman

Registration Fee:

• USD 100

 Prize Bifurcation:

•  USD 500 (1st Prize) | USD 300 (2nd Prize) |USD 250 (3rd Prize)

 Registration mode: Online.

Accommodation : For inquiries regarding Hospitality Partners you can contact on this Number +97152780945

For Any Query:
Feel Free To Call : +97152780945
Email: contact@roboticsolympaids.com